To set up your new Synology router, first, unbox it. After that, begin the synology router setup by connecting the power cable to the router. Turn on the router and connect it to your local network. After that, complete the setup wizard on the Synology router official site. To know more about the setup, perform the instructions given below.
Position the antenna at the antenna base and turn it clockwise to attach it firmly to the router.
Install the other antenna and position them at 90 degrees to obtain a strong Wi-Fi signal for synology router rt2600ac setup.
Place the Synology router on a flat surface and make sure there is no interference between the router and the device to be connected.
Ensure that there are no electrical devices placed near the router. Their signals might interfere.
Also note that the router should not be placed near metal objects, glass door, or concrete for synology router rt2600ac setup.
Attach the power cord to the Synology router setup and the power outlet and turn on the router.
Wait till the Status and WAN lights turn green. From your wireless device, scan the QR code and connect to the Wi-Fi network.
Make use of the network cable to connect your devices to the Synology router.
Open the default browser on the device that you have connected and enter the Synology router’s IP address.
Open the SRM Setup Wizard to complete the synology router rt2600ac setup.
SYNOLOGY ROUTER VPN SETUP
The first solution is to enable the PPTP VPN server. To do so, open the VPN Server and select the PPTP option under the Settings menu.
Highlight the checkbox near the Enable PPTP VPN Server option to enable VPN on synology router setup.
In the Dynamic Address Field, key in the IP address of the virtual server for synology router vpn setup.
Set the ‘Maximum Connection Number’ and the ‘Maximum Number of Connection With Same Account’ options to restrict the number of wireless devices that can be connected.
Choose the Authentication Method as PAP or MS-CHAP v2. In case you select the MS-CHAP v2 option, then select an encryption type from No MPPE, Require MPPE(40/128 bit) or Maximum MPPE(128 bit)
To restrict the packet size of the data, set MTU for synology router vpn setup.
Specify the DNS server’s IP address after enabling the Use Manual DNS option. Tap Apply button to save the changes.
Similarly, enable the OpenVPN VPN Server and mark the checkbox near the Enable Compression on the VPN Link option.
Enable the Allow Clients to Access Server’s LAN option and the IPv6 Server Mode on synology setup router.
Go to Network Center and select the Internet option. Choose the Connection option. Click the Apply button for synology router vpn setup.
Next, enable the L2TP/IPSec VPN Server. Make sure it runs in the Kernel Mode to get the maximum performance.
Enter a Pre-shared Key and tick the checkbox near the Enable SHA2-256 Compatible Mode(96-bit) option for synology router vpn setup.
Tap the Apply button present at the bottom of the screen to save the synology router setup settings you have changed.
SYNOLOGY ROUTER TRAFFIC CONTROL
When the Synology NAS is in the router mode, the router traffic control would be allowed to do its purpose. This router traffic control will also manage the uploading and the downloading of the traffic that your Synology network meets. Create rules by specifying your Guaranteed Bandwidth and Maximum Bandwidth so that the traffic can be controlled on Synology Router Settings.
You can also create a router traffic control rule,
First, you have to choose Network from the drop-down menu.
Then, click the Create option.
Next, you will find the Ports section. Select the All option so that you can apply the rule to all the ports.
You can now find a Source IP section. Select the Specific IP option and click the Select option.
To delete the router traffic, in the enabled column of the list, you have to uncheck the checkbox.
Then, erase or delete the router traffic control rule.
LINK AGGREGATION SYNOLOGY ROUTER
Link Aggregation on synology router setup is used to combine the LAN interfaces and the multi LAN which is supported by the NAS. It also enlarges the bandwidth of the Synology NAS by totaling the multiple Network also maintains network connection by providing traffic failover in case the connection is down.
To Combine Multiple LANs,
First, go to the control panel. Then, select the Network and then select the Network Interface.
Now, click the Create Bond option.
Then, choose for a mode. You can select from Adaptive load balancing, IEEE 802.3ad Dynamic Link Aggregation, Balance XOR, Active/standby.
Next, specify the interfaces so that you can create the Link Aggregation Synology Router.
Now, configure the synology router settings and then click the Apply option. The synology setup router is now complete.
Now, you can see the new interface named Bond 1 on the list.
To Edit Link Aggregation,
First, go to the Control Panel and then select Network and then choose the Network Interface option of Link Aggregation Synology Router.
Now, choose the interface Bond 1 and then click the edit button.
Now you can modify the settings.
To Remove the Link Aggregation,
The step is to go to the Control panel, select Network, and then click on the Network interface option on link aggregation synology router.
Choose the Delete button by selecting the interface Bond1.
After completing the process, on synology router setup you can see Bond 1 replaced by two interfaces.